How to Shoe a Horse

adminsatu

adminsatu

Lift the horse’s foot.,
Remove any shoes that are already on the horse’s feet.,
Clean the bottom of the hoof.,
Use a hoof knife to remove excess, flaky sole from the bottom of the hoof.,
Trim excess hoof wall with hoof nippers.,
Use a rasp to flatten and level the the sole.,
Size the shoe to its hoof.,
Make minor adjustments to the shape of the shoe, if needed.,
Secure the shoe in its place with nails.,
Bend and remove the nail tips.,
Clinch the nail.,
File any rough spots on the hoof wall.,
Repeat process three more times until all four hooves have been shod.

When working with a horse’s hooves it’s important to move the horse’s foot into position in a way that doesn’t surprise the horse or irritate it. Make sure the horse is aware of your presence by gently patting it on the rump. To get your horse to lift her foot, run your hand down her leg. Then, squeeze the tendon above the ankle and lift the hoof. The horse should shift its weight to its other three feet.While you work, hold the foot in place by tucking your hip against the horse’s hock (the large joint on the hind leg) and gaskin (the muscle above the hock). Use the inside of your knee to pull the foot out slightly and up between your legs so that the sole of the hoof faces up towards you. Support the horse’s toe with one hand. This position locks the horse’s foot in place, making it difficult for the horse to kick or put its foot on the ground before you’re done working.
Make sure that you reward your horse with praise for cooperating and waiting while you clean her hooves. Saying, “good girl” or “yes” after she lifts each hoof for you will help to reinforce your horse’s good behavior.;
, To remove a horseshoe, first, “break” (straighten) the nail clinches (the bent tips of each nail that holds the shoe on) with a clinch cutter and a hammer. Work the blade of the clinch cutter under the clinch, then hit it with a hammer to straighten the nail. Then, use a pair of metal pull-offs to loosen and remove the shoe. Close the jaws of the pull-offs around the outside heel of the shoe and use an outside to center rocking motion, working towards the toe to loosen the shoe. Repeat for the inside heel and proceed in this fashion until the shoe can be pulled off.Several alternatives exist for breaking the nail clinches. In a pinch, you can use a rock and a flat head screwdriver to bend the nail tips upwards, or, if you’re careful not to wear a hole in the hoof wall, you can even use a rasp to file the nail clinches away.

, For your horse’s health and safety, you don’t want dirt or debris trapped between its new shoe and its foot. Before shoeing your horse, use a hoof pick to remove any compacted dirt, mud, rocks, manure, etc. from your horse’s foot. Use downward strokes from heel to toe. Follow the hoof pick with a wire brush for added cleanliness.Take care around the frog – the triangular portion in the middle of the hoof. This part of the hoof is extra-sensitive.

, Typically, before a horse is shod, the dark, hard, outer layer of each hoof’s sole is removed to reveal the softer, whiter material underneath in a process roughly equivalent to trimming a human’s toenails. Take care not to cut too deep, or you risk hurting the horse or even rendering it temporarily lame – the same as if you’d cut a person’s nails too short.This process is easiest if you keep your hoof knife razor sharp. But use caution. It’s easy to accidentally slip and cut yourself while working.

, The hoof wall – the edge of the hoof – should extend about 3 inches (7.6 cm) to 3 & 3/4 inches from the hairline above the hoof itself. If it’s any longer, use a set of nippers (essentially giant nail clippers) to trim the edge of the hoof to a suitable length.You should see a ridge where the hoof wall extends beyond the sole. Do not cut into the sole with the nippers, or you may injure the horse.When you trim the hoof with nippers, be sure to keep the trimmed edges of the hoof uniformly straight and level so that they’ll sit flush with the ground. Trim from each side of the heel to the toe.

The exception to this is in cases where a horse’s gait wears its hoof unevenly – in this case, you’ll want to take slightly less hoof material off of the side that the horse favors. Use caution when making this distinction and, if unsure, consult an experienced farrier.

, The very last thing that must be done to prepare the hoof for its shoe is to ensure the bottom of the hoof is smooth, flat and level. Use a rasp to gently file any uneven spots on the bottom of the hoof, taking care, as always, not to wear the hoof too short or irritate the frog. Then using your knife, pare away slightly to bevel the sole away from the hoof wall. Contact of the sole on the shoe can cause the horse discomfort., As with human feet, horse feet come in many different sizes and, thus, different horses will require different-sized shoes. Before proceeding, ensure that the shoes you have available are the correct size for your horse’s feet. Note that a horse’s front and hind feet are differently-shaped, so you will need different shoes for each.most horses have a size smaller in the back then the front, but not always.

If you have to choose between shoes that are slightly too big and shoes that are slightly too small, choose the bigger shoes. These can be bent, shaped, and ground down to a smaller size, while too-small shoes can’t be made bigger. Too long a shoe in front will cause the horse to step on the exposed heel of the shoe and pull it off.

, Often, even if horse shoes are the correct size, they will not fit a horse’s foot without adjustments. Like human feet, horse feet can be asymmetrical or uneven. There are several ways to custom-shape horseshoes.

If you’re a knowledgeable metalworker, you can heat the shoe until the steel can be bent to the size of the hoof.
Or, you can cold shape the shoe on an anvil using a hammer and tongs.
Some farriers do neither, opting instead to grind their shoes down until they fit with a rasp or grinding machine.

Well-fitting horse shoes should align well with the edge of the hoof. Keep in mind that it may take some time to get a shoe to the perfect size for your horse.

, Align the shoe so that it sits perfectly against the edge of the hoof, then drive nails through the holes in the shoe to fix it to the horse’s foot. When doing this, care must be taken so as not to hurt or hobble the horse.

Drive the nail through the hoof at an outward angle so that the nail tips go through the top of the hoof wall.

Never drive nails into the sensitive inner portion of the hoof. To make this easier, use hoof nails that have a bevel on one side to guide the tip through the hoof wall.With these special nails, the manufacturer’s stamp on the side of the nail head should face the center of the foot (towards the frog) – this ensures that the bevel is facing the right direction.
Some modern horseshoes use glue, rather than nails, to hold the shoe in place.If you’re worried about hurting your horse, you may want to try this alternative. Note that application methods for glue-on shoes can vary – consult the manufacturer or an experienced farrier for more information.

, Once each nail has been driven, use the claw end of your hammer to bend the tip of the nail over against the hoof wall. Then, twist off the tip or use a pair of nippers to bend and clip the tips off. Try leave about 1/8″ of the tip bent over the edge of the hole formed by the nail pointing towards the toe. This ensures that the nail will hold the shoe in place without the sharp tip hurting you or the horse.

, Set a clinch block under the nail on the outer hoof wall, then set the nail in the hoof (or “clinch” it) by hitting the nail head once again with the driving hammer. This gives the nail a firm grip in the horse’s hoof, ensuring the shoe stays in place. You may use a sturdy metal tool, like your nippers, in place of the clinch block in a pinch.

Another option is to use a special tool called a clincher. With this tool, all you need to do is align the jaws of the clincher over the nail tip and squeeze the handles.

, Finally, give the outside of the hoof a once-over with a rasp, smoothing out any uneven spots and giving the hoof a nice clean finish. Pay special attention to the clinched nail tips, which can also be filed smooth.When finished, you should be able to draw a cloth over the hoof wall without it catching.

You may also notice that excess hoof material protrudes over the edge of the shoe. If this is the case, use a pair of nippers or pull-offs to remove it.

, Remember that the front and back hooves will require differently-shaped shoes and that even the two front and back feet may not be perfectly symmetrical with each other.

Comments are disabled.